Subaru Enthusiasts Car Club of the Sierras  

Go Back   Subaru Enthusiasts Car Club of the Sierras > Search Forums
Reload this Page Search Results
FAQ Calendar Today's Posts Search

Showing results 1 to 14 of 14
Search took 0.00 seconds. Search: Posts Made By: swr999
Forum: Technical Chat 2012-05-19, 10:48 PM
Replies: 3
Views: 2,243
Posted By swr999
Thanks Dean. I'll check with Matt.

Thanks Dean. I'll check with Matt.
Forum: Technical Chat 2012-05-19, 07:38 PM
Replies: 3
Views: 2,243
Posted By swr999
Turbo inlet hose recommendation?

Hello all,

My OEM turbo inlet hose has split at the turbo junction.

Any recommendations on what's a good replacement?
Or what to stay away from?

The install can be a PITA. The Perrin...
Forum: Technical Chat 2011-03-25, 03:51 PM
Replies: 3
Views: 1,582
Posted By swr999
I had a persistent P0457 (every 3-4 days) prior...

I had a persistent P0457 (every 3-4 days) prior to pulling my motor to cure a spun rod bearing. New fuel cap made no difference. After reinstalling the motor (about a year ago now) I never got...
Forum: Technical Chat 2010-07-28, 08:49 PM
Replies: 7
Views: 1,488
Posted By swr999
Most any muffler shop will test the cat...

Most any muffler shop will test the cat backpressure for free.
Forum: Technical Chat 2010-07-28, 08:41 PM
Replies: 18
Views: 5,717
Posted By swr999
Manual transmission? Slipping clutch. You'll...

Manual transmission? Slipping clutch. You'll notice it more in higher gears. Replacing it is the fix.
Forum: Technical Chat 2010-04-25, 05:40 PM
Replies: 14
Views: 5,007
Posted By swr999
Well, I'm giving the StopTechs a try (the...

Well, I'm giving the StopTechs a try (the "Performance Street"). Installed them (F&R) yesterday and did a couple sets of bed-ins. Got 'em pretty hot and no noticeable fade. No bad behavior so far....
Forum: Technical Chat 2010-04-16, 04:16 PM
Replies: 14
Views: 5,007
Posted By swr999
But, back to the StopTechs; I assume they are a...

But, back to the StopTechs; I assume they are a new formulation, not a relabeled pad from somebody else? I couldn't find much information on the StopTech website besides a bar graph.

When I do a...
Forum: Technical Chat 2010-04-15, 09:19 PM
Replies: 14
Views: 5,007
Posted By swr999
Question Opinions on Axxis ULT and StopTech pads?

Any opinions on the Axxis/PBR ULT pads, and the StopTech "Performance" street pads? The application is mostly street with occasional HPDE track use. $$ is a consideration, but not the only one. Don't...
Forum: Technical Chat 2010-02-28, 10:57 PM
Replies: 139
Views: 41,001
Posted By swr999
I changed out my in-tank fuel filter a couple...

I changed out my in-tank fuel filter a couple weeks ago, just on general principles (at 87k miles). The old one was discolored but showed no signs of clogging or any deterioration. It could be...
Forum: Technical Chat 2010-02-28, 01:43 PM
Replies: 4
Views: 2,053
Posted By swr999
Hey Dean! Good to hear from you. How's...

Hey Dean!
Good to hear from you.
How's everything going? By chance are you going to be at Pahrump? I'll be there...
-Steve
Forum: Technical Chat 2010-02-28, 01:33 PM
Replies: 4
Views: 2,053
Posted By swr999
Thanks for your reply. I don't see smoke, but...

Thanks for your reply.
I don't see smoke, but possibly at sustained 3000+ RPM I might not be noticing some smoke if it is happening.???
Forum: Technical Chat 2010-02-28, 10:41 AM
Replies: 4
Views: 2,053
Posted By swr999
An oil usage question

Background: I recently finished up a rebuild following a spun rod bearing 'event'. Stock '05 STi. Rebuild included JE skirt-coated pistons, new OEM Sti crank. complete valve job. Car runs fine, has...
Forum: Technical Chat 2010-02-23, 08:30 PM
Replies: 24
Views: 6,589
Posted By swr999
Just a minor comment. When re-assembling my motor...

Just a minor comment. When re-assembling my motor I reused the timing belt tensioner. A drill press worked nicely to compress it (slowly) in the vertical orientation. Not sure why vertical is part of...
Forum: Technical Chat 2010-02-23, 07:36 PM
Replies: 31
Views: 9,163
Posted By swr999
Maybe the disc isn't sliding easily on the input...

Maybe the disc isn't sliding easily on the input shaft and stays up close to the flywheel tending to turn the input shaft while going into gear? Did the disc slide easily on the input shaft when you...
Showing results 1 to 14 of 14

 
Forum Jump

All times are GMT -8. The time now is 12:34 AM.

SECCS Homepage - Archive - Top

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
All Content Copyright Subaru Enthusiasts Car Club of the Sierras unless otherwise noted.